Creating the Install required updates and fix vulnerabilities task
Expand all | Collapse all
The Install required updates and fix vulnerabilities task is only available under the Vulnerability and Patch Management license.
The Install required updates and fix vulnerabilities task is used to update and fix vulnerabilities in third-party software, including Microsoft software, installed on the managed devices. This task allows you to install multiple updates and fix multiple vulnerabilities according to certain rules.
To install updates or fix vulnerabilities by using the Install required updates and fix vulnerabilities task, you can do one of the following:
To create the Install required updates and fix vulnerabilities task:
- In the main menu, go to DEVICES → TASKS.
- Click Add.
The Add Task Wizard starts. Follow the steps of the Wizard.
- For the Kaspersky Security Center application, select the Install required updates and fix vulnerabilities task type.
- Specify the name for the task that you are creating. A task name cannot be more than 100 characters long and cannot include any special characters ("*<>?\:|).
- Select devices to which the task will be assigned.
- Specify the rules for update installation, and then specify the following settings:
- Start installation at device restart or shutdown
If this option is enabled, updates are installed when the device is restarted or shut down. Otherwise, updates are installed according to a schedule.
Use this option if installing the updates might affect the device performance.
By default, this option is disabled.
- Install required general system components
If this option is enabled, before installing an update the application automatically installs all general system components (prerequisites) that are required to install the update. For example, these prerequisites can be operating system updates
If this option is disabled, you may have to install the prerequisites manually.
By default, this option is disabled.
- Allow installation of new application versions during updates
If this option is enabled, updates are allowed when they result in installation of a new version of a software application.
If this option is disabled, the software is not upgraded. You can then install new versions of the software manually or through another task. For example, you may use this option if your company infrastructure is not supported by a new software version or if you want to check an upgrade in a test infrastructure.
By default, this option is enabled.
Upgrading an application may cause malfunction of dependent applications installed on client devices.
- Download updates to the device without installing them
If this option is enabled, the application downloads updates to the device but does not install them automatically. You can then Install downloaded updates manually.
Microsoft updates are downloaded to the system Windows storage. Updates of third-party applications (applications made by software vendors other than Kaspersky and Microsoft) are downloaded to the folder specified in the Folder for downloading updates field.
If this option is disabled, the updates are installed to the device automatically.
By default, this option is disabled.
- Folder for downloading updates
This folder is used to download updates of third-party applications (applications made by software vendors other than Kaspersky and Microsoft).
- Enable advanced diagnostics
If this feature is enabled, Network Agent writes traces even if tracing is disabled for Network Agent in Kaspersky Security Center Remote Diagnostics Utility. Traces are written to two files in turn; the total size of both files is determined by the Maximum size, in MB, of advanced diagnostics files value. When both files are full, Network Agent starts writing to them again. The files with traces are stored in the %WINDIR%\Temp folder. These files are accessible in the remote diagnostics utility, you can download or delete them there.
If this feature is disabled, Network Agent writes traces according to the settings in Kaspersky Security Center Remote Diagnostics Utility. No additional traces are written.
When creating a task, you do not have to enable advanced diagnostics. You may want to use this feature later if, for example, a task run fails on some of the devices and you want to get additional information during another task run.
By default, this option is disabled.
- Maximum size, in MB, of advanced diagnostics files
The default value is 100 MB, and available values are between 1 MB and 2048 MB. You may be asked to change the default value by Kaspersky Technical Support specialists when information in the advanced diagnostics files sent by you is not enough to troubleshoot the problem.
- Specify the operating system restart settings:
- Do not restart the device
Client devices are not restarted automatically after the operation. To complete the operation, you must restart a device (for example, manually or through a device management task). Information about the required restart is saved in the task results and in the device status. This option is suitable for tasks on servers and other devices where continuous operation is critical.
- Restart the device
Client devices are always restarted automatically if a restart is required for completion of the operation. This option is useful for tasks on devices that provide for regular pauses in their operation (shutdown or restart).
- Prompt user for action
The restart reminder is displayed on the screen of the client device, prompting the user to restart it manually. Some advanced settings can be defined for this option: text of the message for the user, the message display frequency, and the time interval after which a restart will be forced (without the user's confirmation). This option is most suitable for workstations where users must be able to select the most convenient time for a restart.
By default, this option is selected.
- Repeat prompt every (min)
If this option is enabled, the application prompts the user to restart the operating system with the specified frequency.
By default, this option is enabled. The default interval is 5 minutes. Available values are between 1 and 1440 minutes.
If this option is disabled, the prompt is displayed only once.
- Restart after (min)
After prompting the user, the application forces restart of the operating system upon expiration of the specified time interval.
By default, this option is enabled. The default delay is 30 minutes. Available values are between 1 and 1440 minutes.
- Wait time before forced closure of applications in blocked sessions (min)
Applications are forced to close when the user's device goes locked (automatically after a specified interval of inactivity, or manually).
If this option is enabled, applications are forced to close on the locked device upon expiration of the time interval specified in the entry field.
If this option is disabled, applications do not close on the locked device.
By default, this option is disabled.
- If you want to modify the default task settings, enable the Open task details when creation is complete option on the Finish task creation page. If you do not enable this option, the task is created with the default settings. You can modify the default settings later, at any time.
- Click the Finish button.
The task is created and displayed in the list of tasks.
- Click the name of the created task to open the task properties window.
- In the task properties window, specify the general task settings according to your needs.
- Click the Save button.
The task is created and configured.
If the task results contain a warning of the 0x80240033 "Windows Update Agent error 80240033 ("License terms could not be downloaded.")" error, you can resolve this issue through the Windows Registry.
Page top
[Topic 182671]